A microprocessor is a programmable digital electronic component that incorporates the functions of a central processing unit (CPU) on a single semiconducting integrated circuit (IC). The microprocessor was born by reducing the word size of the CPU from 32 bits to 4 bits, so that the transistors of its logic circuits would fit onto a single part. One or more microprocessors typically serve as the CPU in a computer system, embedded system, or handheld device. A device that integrates the functions of the central processing unit (CPU) of a computer onto one semiconductor chip or integrated circuit (IC). In essence, the microprocessor contains the core elements of a computer system, its computation and control engine. Only a power supply, memory, peripheral interface ICs, and peripherals (typically input/output and storage devices) need be added to build a complete computer system.
CISC Chips
Pronounced sisk, and stands for Complex Instruction Set Computer. Most PC's use CPU based on this architecture. For instance Intel and AMD CPU's are based on CISC architectures. Typically CISC chips have a large amount of different and complex instructions. The philosophy behind it is that hardware is always faster than software, therefore one should make a powerful instructionset, which provides programmers with assembly instructions to do a lot with short programs. In common CISC chips are relatively slow (compared to RISC chips) per instruction, but use little (less than RISC) instructions. A complex instruction set computer (CISC) is a microprocessor instruction set architecture (ISA) in which each instruction can execute several low-level operations, such as a load from memory, an arithmetic operation, and a memory store, all in a single instruction. The term was retroactively coined in contrast to reduced instruction set computer (RISC).
CISC
Emphasis on hardware
Includes multi-clockcomplex instructions
Memory-to-memory:"LOAD" and "STORE"incorporated in instructions
Small code sizes,high cycles per second
Transistors used for storingcomplex instructions
RISC Chips
Pronounced risk, and stands for Reduced Instruction Set Computer. RISC chips evolved around the mid-1980 as a reaction at CISC chips. The philosophy behind it is that almost no one uses complex assembly language instructions as used by CISC, and people mostly use compilers which never use complex instructions. Apple for instance uses RISC chips. Therefore fewer, simpler and faster instructions would be better, than the large, complex and slower CISC instructions. However, more instructions are needed to accomplish a task. An other advantage of RISC is that - in theory - because of the more simple instructions, RISC chips require fewer transistors, which makes them easier to design and cheaper to produce. The reduced instruction set computer, or RISC, is a CPU design philosophy that favors an instruction set reduced both in size and complexity of addressing modes, in order to enable easier implementation, greater instruction level parallelism, and more efficient compilers. As of 2007, common RISC microprocessors families include the DEC Alpha, ARC, ARM, AVR, MIPS, PA-RISC, Power Architecture (including PowerPC), and SPARC.
RISC
Emphasis on software
Single-clock,reduced instruction only
Register to register:"LOAD" and "STORE"are independent instructions
Low cycles per second,large code sizes
Spends more transistorson memory registers
Memory Chips
A chip that holds programs and data either temporarily (RAM), permanently (ROM, PROM) or permanently until changed (EPROM, EEPROM, flash memory).
Kinds of Memory Chips
*SIMMS
The term SIMM stands for Single In-Line Memory Module. With SIMMs, memory chips are soldered onto a modular printed circuit board (PCB), which inserts into a socket on the system board. The first SIMMs transferred 8 bits of data at a time. Later, as CPUs began to read data in 32-bit chunks, a wider SIMM was developed, which could supply 32 bits of data at a time. The easiest way to differentiate between these two different kinds of SIMMs was by the number of pins, or connectors. The earlier modules had 30 pins and the later modules had 72 pins. Thus, they became commonly referred to as 30-pin SIMMs and 72-pin SIMMs.
*DIMMS
Dual In-line Memory Modules, or DIMMs, closely resemble SIMMs. Like SIMMs, most DIMMs install vertically into expansion sockets. The principal difference between the two is that on a SIMM, pins on opposite sides of the board are "tied together" to form one electrical contact; on a DIMM, opposing pins remain electrically isolated to form two separate contacts. DIMMs come in various form factors and are specific to different DRAM technologies. 168-pin DIMM: EDO and PC66/100/133 SDRAM 184-pin DIMM: DDR 200/266/333/400 DDR SDRAM 240-pin DIMM: DDR2 400/533/667/800 DDR-2 SDRAM DIMMs transfer 64 bits of data at a time and are typically used in computer configurations that support a 64-bit or wider memory bus. Some of the physical differences between DIMMs and 72-pin SIMMs include: the length of module, the number of notches on the module, and the way the module installs in the socket. Another difference is that many 72-pin SIMMs install at a slight angle, whereas DIMMs install straight into the memory socket and remain completely vertical in relation to the system motherboard. The illustration below compares a 168-pin DIMM to a 72-pin SIMM.
*SO DIMMs
A type of memory commonly used in notebook computers is called SO DIMM or Small Outline DIMM. The principal difference between a SO DIMM and a DIMM is that the SO DIMM, because it is intended for use in notebook computers, is significantly smaller than the standard DIMM. The 72-pin SO DIMM is 32 bits wide and the 144-pin SO DIMM is 64 bits wide. 144-pin and 200-pin modules are the most common SO DIMMs today.
*MicroDIMM
(Micro Dual In-Line Memory Module) Smaller than an SO DIMM, MicroDIMMs are primarily used in sub-notebook computers. MicroDIMMs are available in 144-pin SDRAM, 172-pin DDR and 214-pin DDR2.
*RIMMS AND SO-RIMMS
RIMM is the trademarked name for a Direct Rambus memory module. RIMMs look similar to DIMMs, but have a different pin count. RIMMs transfer data in 16-bit chunks. The faster access and transfer speed generates more heat. An aluminum sheath, called a heat spreader, covers the module to protect the chips from overheating. A 184-pin Direct Rambus RIMM shown with heat spreaders pulled away.
An SO-RIMM looks similar to an SO DIMM, but it uses Rambus technology.
*FLASH MEMORY
Flash memory is a solid-state, non-volatile, rewritable memory that functions like RAM and a hard disk drive combined. Flash memory stores bits of electronic data in memory cells, just like DRAM, but it also works like a hard-disk drive in that when the power is turned off, the data remains in memory. Because of its high speed, durability, and low voltage requirements, flash memory is ideal for use in many applications - such as digital cameras, cell phones, printers, handheld computers, pagers, and audio recorders. Flash memory is available in many different form factors, including: CompactFlash, Secure Digital, SmartMedia, MultiMedia and USB Memory.
Expansion Slots
An opening in a computer where a circuit board can be inserted to add new capabilities to the computer. Nearly all personal computers except portables contain expansion slots for adding more memory, graphics capabilities, and support for special devices. The boards inserted into the expansion slots are called expansion boards, expansion cards , cards , add-ins , and add-ons.
Expansion slots for PCs come in two basic sizes: half- and full-size. Half-size slots are also called 8-bit slots because they can transfer 8 bits at a time. Full-size slots are sometimes called 16-bit slots. In addition, modern PCs include PCI slots for expansion boards that connect directly to the PCI bus.
Troubleshooting a motherboard problem is like trouble shooting your car when it won't
start. Is the battery dead, is it out of gas, is the spark getting to the spark plugs. See where
I am going with this. Your problem could be any where from the power cord plugged into
the wall socket all the way to the keyboard.
When you have a problem and have ruled out all the external devices [mouse, keyboard,
commercial power, and monitor] then you start on the internal devices, hard drive, cd
rom, floppy, video card, any installed auxiliary cards like the sound card, NIC, power
supply, and so forth.
One indication that your motherboard is experiencing problems is when you power it up
and goes straight into the BIOS setup. Some times you will get an error message about
why it went into the BIOS setup, some times nothing but the setup screen. Another
indication is with the newer motherboard one of the embedded devices has failed, you
can press on and install a card to replace that device or if under warranty send it back to
the manufacture for repair or replacement.
So what is your motherboard doing that is out of the ordinary? Not starting at all? Dumps
to BIOS setup? Can't see the hard drive or cd rom? Mouse not working or intermittent?
Keyboard not functioning? No sound from the embedded sound device? No network
connectivity from the embedded NIC? Your USB will not connect on one or more ports? 
RepairITware is a Leeds Based Computer Repair and Maintenance service in Leeds for your home PC, we carry over 10 years experience in the industry so you can rest assure your computer is in good hands.
RepairITware also offer Website design service, if you have a small company you want to get on to the website to advertise your products and services, we can build a simple website to promote your business please 
